ip default-network和ip route 0.0.0.0 0.0.0.0默认路由的区别
字体：[ ] 类型：转载 时间：
在自己的2501上研究这三种默认路由的区别.指定默认路由（last resort gateway）的指令供有3种，可以分成两类：1、ip default-gateway当路由器上的ip routing无效时，使用它指定默认路由，用于RXBoot模式（no ip routing）下***IOS等。或者关闭ip routing 让路由器当主机用,此时需要配置默认网关2、ip default-network和ip route 0.0.0.0 0.0.0.0两者都用于ip routing有效的路由器上，区别主要在于路由协议是否传播这条路由信息。比如：IGRP无法识别0.0.0.0，因此传播默认路由时必须用ip default-network。当用ip default-network指令设定多条默认路由时，administrative distance最短的成为最终的默认路由；如果有复数条路由distance值相等，那么在路由表（show ip route）中靠上的成为默认路由。同时使用ip default-network和ip route 0.0.0.0 0.0.0.0双方设定默认路由时，如果ip default-network设定的网络是直连（静态、且已知）的，那么它就成为默认路由；如果ip default-network指定的网络是由交换路由信息得来的，则ip route 0.0.0.0 0.0.0.0指定的表项成为默认路由。最后，如果使用多条ip route 0.0.0.0 0.0.0.0指令，则流量会自动在多条链路上负载均衡。官方详细文档点这里 例子:关闭ip routing 举例:mycisco(config)#no ip routing mycisco(config)#ip default-gateway 192.168.0.1 mycisco(config)#endmycisco#ping Type escape sequence to abort.Sending 5, 100-byte ICMP Echoes to 61.152.167.75, timeout is 2 seconds:!!!!!Success rate is 100 percent (5/5), round-trip min/avg/max = 60/60/60 msmycisco#show ip routeDefault gateway is 192.168.0.1Host&&&&&&&&&&&&&& Gateway&&&&&&&&&& Last Use&&& Total Uses& InterfaceICMP redirect cache is emptymycisco#ip route例子:ip route 0.0.0.0 0.0.0.0 192.168.0.1mycisco#ping Type escape sequence to abort.Sending 5, 100-byte ICMP Echoes to 61.152.167.75, timeout is 2 seconds:!!!!!Success rate is 100 percent (5/5), round-trip min/avg/max = 56/56/60 msmycisco#show ip routeCodes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP&&&&&& D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area &&&&&& E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP&&&&&& i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, * - candidate default&&&&&& U - per-user static routeGateway of last resort is 192.168.0.1 to network 0.0.0.0C&&& 1.0.0.0/8 is directly connected, Loopback0C&&& 192.168.0.0/24 is directly connected, Ethernet0S*&& 0.0.0.0/0 [1/0] via 192.168.0.1mycisco#ip default-network 必须是在所到网络已经存在路由的情况下,否则执行无效.mycisco(config)#ip route 61.0.0.0 255.0.0.0 192.168.0.1mycisco#show ip routeCodes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP&&&&&& D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area &&&&&& E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP&&&&&& i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, * - candidate default&&&&&& U - per-user static routeGateway of last resort is not setC&&& 1.0.0.0/8 is directly connected, Loopback0S&&& 61.0.0.0/8 [1/0] via 192.168.0.1C&&& 192.168.0.0/24 is directly connected, Ethernet0接着我们执行:mycisco(config)#ip default-network 61.0.0.0再看路由表:mycisco#show ip routeCodes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP&&&&&& D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area &&&&&& E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP&&&&&& i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, * - candidate default&&&&&& U - per-user static routeGateway of last resort is 192.168.0.1 to network 61.0.0.0C&&& 1.0.0.0/8 is directly connected, Loopback0S*&& 61.0.0.0/8 [1/0] via 192.168.0.1C&&& 192.168.0.0/24 is directly connected, Ethernet0
文章录入：csh&&&&责任编辑：csh&
大家感兴趣的内容
12345678910
最近更新的内容
常用在线小工具ip route 0.0.0.0 0.0.0.0和ip defult-network区别
ip route 0.0.0.0 0.0.0.0和ip
defult-network区别
哪位能说说ip route 0.0.0.0 0.0.0.0和ip default-network命令的区别吗？
我所知道的ip route 命令会向路由表里加一条静态路由，ip
default-network命令不会
ip route 命令按接口和地址指定缺省路由ip default-network命令按网络指定
谁能说说还有什么区别？以及在什么情况下使用哪条吗？还有他们在再发布时的区别！
FW:发信人: canway()
整理人: sanjose( 10:54:44), 站内信件
听了各位解释，有些明白，可是路由器没有路由还叫路由器吗，那样两个命令
功能似乎是一样的，都是把不知道到的包发给下一个站点，可是我在做一个项目
设置ip default-gateway就不行。用ip route 0.0.0.0 0.0.0.0 xxxxxxxx
就通了。 是不是这样，对于ip default-gateway来说，只有对这个网段才有效，
网段路由过来的其他网段的信息到了用ip default-gateway的网段就不能利用这
个 命令传送，而是要用ip route 0.0.0.0 0.0.0.0.了。也就是ip route 0.0.0
0.0.0.0才能完成路由功能，不知道理解的对吗
1。 ip default-gateway用与路由器不作路由时使用，这时路由器就只是一台主
机好象Win95PC一样需要配一个网关才能与外界通信。
如果 “no ip routing&则路由器就不作路由。这时你可以配bridge-group，把路
由表及里器当switch使。
2。 ip route 0.0.0.0 0.0.0.0 用于履行路由功能。如果ip routin
g是enable的则ip default-gateway不起作用.
FW:区别在于，ip route本机生效，ip default-network可以影响整个路由协议域
/en/US/customer...shtml#ipnetwork
FW:Introduction
This Tech Note explains how to configure a default route, or gateway of last resort,
using the following IP commands: ip default-gateway, ip default-network, and ip route
0.0.0.0 0.0.0.0. Let's look at each of these commands in more detail.
Before You Begin
Conventions
For more information on document conventions, see the Cisco Technical Tips Conventions.
Prerequisites
There are no specific prerequisites for this document.
Components Used
This document is not restricted to specific software and hardware versions.
The information presented in this document was created from devices in a specific lab
environment. All of the devices used in this document started with a cleared (default)
configuration. If you are working in a live network, ensure that you understand the
potential impact of any command before using it.
ip default-gateway
The ip default-gateway command differs from the other two commands in that it should
only be used when ip routing is disabled on the Cisco router.
For instance, if the router is a host in the IP world, you can use this command to
define a default gateway for it. You might also use this command when your low end Cisco
router is in boot mode in order to TFTP a Cisco IOS& Software image to the router. In
boot mode, the router doesn't have ip routing enabled.
ip default-network
Unlike the ip default-gateway command, you can use ip default-network when ip routing
is enabled on the Cisco router. When you configure ip default-network the router considers
routes to that network for installation as the gateway of last resort on the router.
For every network configured with ip default-network, if a router has a route to that
network, that route is flagged as a candidate default route. Let's look at the following
routing table taken from a Cisco router:
2513#show ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, * - candidate default
Gateway of last resort is not set
161.44.0.0 255.255.255.0 is subnetted, 1 subnets
C 161.44.192.0 is directly connected, Ethernet0
S 198.10.1.0 [1/0] via 161.44.192.2
131.108.0.0 255.255.255.0 is subnetted, 1 subnets
C 131.108.99.0 is directly connected, TokenRing0
Note the static route to 198.10.1.0 via 161.44.192.2 and that the gateway of last
resort isn't set. If we configure ip default-network 198.10.1.0, the routing table changes
to the following:
2513#show ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, * - candidate default
Gateway of last resort is 161.44.192.2 to network 198.10.1.0
161.44.0.0 255.255.255.0 is subnetted, 1 subnets
C 161.44.192.0 is directly connected, Ethernet0
S 161.44.0.0 255.255.0.0 [1/0] via 161.44.192.0
S* 198.10.1.0 [1/0] via 161.44.192.2
131.108.0.0 255.255.255.0 is subnetted, 1 subnets
C 131.108.99.0 is directly connected, TokenRing0
2513#show ip protocols
We can see the gateway of last resort has now been set as 161.44.192.2. This result is
independent of any routing protocol, as shown by the show ip protocols command at the
bottom of the output.
We can add another candidate default route simply by configuring another instance of ip
default-network:
2513#config terminal
Enter configuration commands, one per line. End with CNTL/Z.
2513(config)#ip route 171.70.24.0 255.255.255.0 131.108.99.2
2513(config)#ip default-network 171.70.24.0
2513(config)#^Z
2513#show ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, * - candidate default
Gateway of last resort is 161.44.192.2 to network 198.10.1.0
161.44.0.0 255.255.255.0 is subnetted, 1 subnets
C 161.44.192.0 is directly connected, Ethernet0
S 161.44.0.0 255.255.0.0 [1/0] via 161.44.192.0
S* 198.10.1.0 [1/0] via 161.44.192.2
171.70.0.0 is variably subnetted, 2 subnets, 2 masks
S 171.70.0.0 255.255.0.0 [1/0] via 171.70.24.0
S 171.70.24.0 255.255.255.0 [1/0] via 131.108.99.2
131.108.0.0 255.255.255.0 is subnetted, 1 subnets
C 131.108.99.0 is directly connected, TokenRing0
Flagging a Default Network
Note: The ip default-network command is classful, which means if the router has a route
to the subnet indicated by this command, it installs the route to the major net. At this
point neither network has been flagged as the default network. The ip default-network
command must be issued again, using the major net, in order to flag the candidate default
2513#config terminal
Enter configuration commands, one per line. End with CNTL/Z.
2513(config)#ip default-network 171.70.0.0
2513(config)#^Z
2513#show ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, * - candidate default
Gateway of last resort is 161.44.192.2 to network 198.10.1.0
161.44.0.0 255.255.255.0 is subnetted, 1 subnets
C 161.44.192.0 is directly connected, Ethernet0
S 161.44.0.0 255.255.0.0 [1/0] via 161.44.192.0
S* 198.10.1.0 [1/0] via 161.44.192.2
171.70.0.0 is variably subnetted, 2 subnets, 2 masks
S* 171.70.0.0 255.255.0.0 [1/0] via 171.70.24.0
S 171.70.24.0 255.255.255.0 [1/0] via 131.108.99.2
131.108.0.0 255.255.255.0 is subnetted, 1 subnets
C 131.108.99.0 is directly connected, TokenRing0
If the original static route had been to the major network, we wouldn't have needed the
extra step of configuring the default network twice.
There are still no IP protocols running here. Without any dynamic protocols running,
you can configure your router to choose from a number of candidate default routes based on
whether the routing table has routes to networks other than 0.0.0.0/0. This command allows
you to configure robustness into the selection of a gateway of last resort. Rather than
configuring static routes to specific next-hops, you can have the router choose a default
route to a particular network by checking in the routing table.
If you lose the route to a particular network, the router selects the second candidate
default, as specified above. You can remove the lost route by removing the static route in
the configuration as follows:
2513#config terminal
Enter configuration commands, one per line. End with CNTL/Z.
2513(config)#no ip route 198.10.1.0 255.255.255.0 161.44.192.2
2513(config)#^Z
%SYS-5-CONFIG_I: Configured from console by console
After removing the static route to the original default network, the routing table
looks like this:
2513#show ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, * - candidate default
Gateway of last resort is 171.70.24.0 to network 171.70.0.0
161.44.0.0 255.255.255.0 is subnetted, 1 subnets
C 161.44.192.0 is directly connected, Ethernet0
S 161.44.0.0 255.255.0.0 [1/0] via 161.44.192.0
* 171.70.0.0 is variably subnetted, 2 subnets, 2 masks
S* 171.70.0.0 255.255.0.0 [1/0] via 171.70.24.0
S 171.70.24.0 255.255.255.0 [1/0] via 131.108.99.2
131.108.0.0 255.255.255.0 is subnetted, 1 subnets
C 131.108.99.0 is directly connected, TokenRing0
Using Different Routing Protocols
Gateways of last resort selected using the ip default-network command are propagated
differently depending on which routing protocol is propagating the default route. For IGRP
and EIGRP to propagate the route, the network specified by the ip default-network command
must be known to IGRP or EIGRP. This means the network must be an IGRP- or EIGRP-derived
network in the routing table, or the static route used to generate the route to the
network must be redistributed into IGRP or EIGRP.
RIP advertises a route to 0.0.0.0. For example, note that the gateway of last resort on
the router below was learned using the combination of the ip route and ip default-network
commands. If we enable RIP on this router, RIP advertises a route to 0.0.0.0 (although not
to the Token Ring network because of split-horizon):
2513(config)#router rip
2513(config-router)#network 161.44.0.0
2513(config-router)#network 131.108.0.0
2513(config-router)#^Z
%SYS-5-CONFIG_I: Configured from console by console
2513#debug ip rip
RIP protocol debugging is on
RIP: sending update to 255.255.255.255 via Ethernet0 (161.44.192.1)
default 0.0.0.0, metric 1
network 131.108.0.0, metric 1
RIP: sending update to 255.255.255.255 via TokenRing0 (131.108.99.1)
network 161.44.0.0, metric 1
Note: In IOS release 12.0T and higher, RIP doesn't advertise the default router if the
route is not learned via RIP. Therefore, it may be necessary to redistribute the route
into RIP, or use the default-information originate command.
OSPF, like RIP, advertises a route for 0.0.0.0 0.0.0.0. However, with OSPF, the router
originating the default route must be configured with the default-information originate
command. For more detailed information, see How Does OSPF Generate Default Routes?.
ip route 0.0.0.0 0.0.0.0
Creating a static route to network 0.0.0.0 0.0.0.0 is another way to set the gateway of
last resort on a router. As with the ip default-network command, using the static route to
0.0.0.0 isn't dependent on any routing protocols. However, ip routing must be enabled on
the router.
Note: IGRP doesn't understand a route to 0.0.0.0, therefore it can't propagate default
routes created using the ip route 0.0.0.0 0.0.0.0 command. Use the ip default-network
command to have IGRP propagate a default route.
EIGRP propagates a route to network 0.0.0.0, but the static route must be redistributed
into EIGRP. RIP and OSPF behave as described when using the ip default-network command.
Keep in mind that the note above still applies.
Let's look at an example of configuring a gateway of last resort using the ip route
0.0.0.0 0.0.0.0 command:
router-3#conf terminal
Enter configuration commands, one per line. End with CNTL/Z.
router-3(config)#ip route 0.0.0.0 0.0.0.0 170.170.3.4
router-3(config)#^Z
router-3#show ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, * - candidate default
U - per-user static route, o - ODR
Gateway of last resort is 170.170.3.4 to network 0.0.0.0
170.170.0.0/24 is subnetted, 2 subnets
C 170.170.2.0 is directly connected, Serial0
C 170.170.3.0 is directly connected, Ethernet0
S* 0.0.0.0/0 [1/0] via 170.170.3.4
Note: If you configure multiple networks as candidate default routes using the ip
default-network command, the network that has the lowest administrative distance is chosen
as the network for the gateway of last resort. If all the networks have the same
administrative distance then the network listed first in the routing table (show ip route
lists the routing table) is chosen as the network for the gateway of last resort. If you
use both the ip default-network and ip route 0.0.0.0 0.0.0.0 commands to configure
candidate default networks, and the network used by the ip default-network command is
known statically, the network defined with the ip default-network command takes precedence
and is chosen for the gateway of last resort. Otherwise if the network used by the ip
default-network command is derived by a routing protocol, the ip route 0.0.0.0 0.0.0.0
command, which will have a lower administrative distance, takes precedence and is chosen
for the gateway of last resort. Lastly, if you use multiple ip route 0.0.0.0 0.0.0.0
commands to configure a default route, traffic is load-balanced over the multiple routes.
To summarize, you can use the ip default-gateway command when ip routing is disabled on
a Cisco router. Use the ip default-network and ip route 0.0.0.0 0.0.0.0 commands to set
the gateway of last resort on Cisco routers that have ip routing enabled. The way in which
routing protocols propagate the default route information varies for each protocol.
FW:0.0.0.0只能标记一条静态缺省路由，ip default-network更灵活，可以标记几条静态缺省路由，路由器可以从中选择开销最小的一个。
0.0.0.0可以在ＲＩＰ、ＥＩＧＲＰ、ＯＳＰＦ中配置，在ＩＧＲＰ中只能用ip
default-network，因为ＩＧＲＰ不能识别网络0.0.0.0/0（ip default-network不能在ＥＩＧＲＰ、ＯＳＰＦ中使用）。如果在ＲＩＰ中同时配置0.0.0.0和ip
default-network，路由器会把0.0.0.0/0作为ｉｐ缺省路由进行传播。
在ＩＯＳ12.1之前的版本中，0.0.0.0在ＲＩＰ自动被传播给其他路由器。在ＩＯＳ12.1中，ＲＩＰ不自动传播静态缺省路由。要传播的话要使用“ｎｅｔｗｏｒ　0.0.0.0”命令，也可以使用
“default-information originate&或&redistribute static&命令。
要想在ＯＳＰＦ中传播静态缺省路由（无论什么版本），也要用&default-information
originate&命令。
“ip default-network”命令是有类别的，如果路由器有一条到用该命令所指示的子网路由，那么它将***一条到其主类网络的静态路由，然后将这条路由标记为一条候选缺省路由。
eigrp 传播默认路由，不需要加 default-information originate，那个命令是给ospf用的，因为它默认不传播default-route