A process model for shot peen forming_文档库
文档库最新最全的文档下载
当前位置： & A process model for shot peen forming
A process model for shot peen forming
Journal of Materials Processing Technology 172(2006)
A process model for shot peen forming
T. Wang a , *, M.J. Platts a , A. Levers b
Institute for Manufacturing, Department of Engineering, University of Cambridge, Mill Lane, Cambridge CB21RX, UK
b Airbus UK Ltd., Broughton, Chester CH40DR, UK
Received 16October 2002; received in revised form 15May 2003; accepted 5September 2005
An equivalent loading unit that can produce a plastic layer was used to model the macroscopic forming effects of shot peening. Because a specificplastic coverage exists in which the individual peen impacts can be regarded as acting independently, their cumulative effects can be assumed to be distributed in the plastic layer as the result of a static load. The loading unit corresponds to the macroscopic stretching strain and can be conveniently calibrated from the peening parameters, such as shot radius, mass flowrate and air pressure. For more intensive peening, the number of loading cycles is in direct proportion to the peening time, which makes the model applicable to practical applications. Compared with experiments, this model gives a good prediction of the peen-formed deflection.(C)2005Elsevier B.V . All rights reserved.
Keywords:S (Shot) P Finite element analysis (FEA)
1. Introduction
It is well known that shot peening the surface of a metal sheet by small hard shot with sufficientkinetic energy can form a specificshape. This is especially used for shaping aircraft wing skin panels. The (shot)peen forming process generally has lower manufacturing costs because there is no need for dies and presses or subsequent thermal processes, and once the process param-eters have been determined, the process is easily reproducible. It also has better adaptability to modern aircraft designs, for example, the capability to form tapered and sculptured integral structures, single and double curved shapes and virtually any size of parts. In addition, peening can provide beneficialper-formance to the peen-formed component like the general shot peen hardening process. In the practial applications, the design of peening parameters for a specificshape has been through trial and error or some numerical methods that are heavily dependent upon tests and experiences.
Homer and VanLuchene [1], VanLuchele et al. [2]and Van-Luchene and Cramer [3]presented a numerical method for predicting peening intensity patterns by assuming the peen form-ing process as a linear finiteelement system responding to the peening induced stresses. Empirical equations determined by
Corresponding author.
E-mail address:tw225@eng.cam.ac.uk(T.Wang).
physical experiments in Boeing Commercial Airplane Group were relied upon to set up the relationship between the induced stresses and the peening intensity. As recognised in their paper, Homer and VanLuchene [1]stated that the experimental data are based on peening of unconstrained specimens but assumed to be applicable for constrained specimens, which may introduce error because in reality various constraints, such as geometry, jigs (pre-stresses)and peening sequences are possible. Other methods or models [4,5]were also based on similar assump-tions, which not only require a large number of tests but may also have problems if constraints are considered.
It has been believed that if the fundamental principle, such as the creation of plasticity by shot peening, can be included in the model, it can simulate the reality more accurately. This can reduce the experimental costs and furthermore, provide a more effective process design. For example, ‘thesqueezed layer model’[6,7]and ‘thethermal stressing model’[8,9]were developed. The squeezed layer method models the peen form-ing process by assuming squeezing of the surface layer of a solid-element model, which requires high computation cost. The thermal stressing model was developed to adopt shell ele-ments based on a stress analysis using the stresses under a single impact and assuming it is equivalent to a full coverage situation (saturationpeening). However, this model is difficultto calibrate for realistic peening applications and the assump-tion of employing the stresses produced by a single impact is disputable.
/$-see front matter (C)2005Elsevier B.V . All rights reserved. doi:10.1016/j.jmatprotec.
Word文档免费下载：
A process model for shot peen forming [J]. Journal of Materials Processing Technology, 9-162. [4] G.H. Majzoobi, R. Azizi, A. A...A Process model f or shot peen forming[ J] . Journal of M at erials Processing T echnology, ) : 159- 162. ( 3) 对喷成形技术是...Forming Technology 吉林大学无模成形技术开发中心 韩奇钢 付文智 冯朋晓 李明哲...A process model for shot peen forming. Journal of Materials Processing ...But the basic shot peening process cannot be efficiently used for all the ...The proposed model is found to predict the surface stresses to an accuracy...The residual stress formed during the shot peening process is simulated numerically. The elastic-plastic constitutive model is adopted to describe the plastic... India a Abstract Modeling shot peening process is very complex as it ...Platts, Finite element impact modelling for shot peen forming, in: ICSP-8... Titanium allyos peening Shot peen forming of metal parts Shot peening for ...Coverage 100% New process: single peening with Zirshot Zirshot Z210 (0.2...Shot Peen Forming Process Based on Temperature Gradient Hu Kaizheng1 Wu J ... The shot peen forming p rocess model p resented herein can be used to ...FE Simulations of Arc-Height Development in Shot-Peened Almen Strips_材料...J., and Levers, A., 2006, “A Process Model for Shot Peen Forming,”... Simulation of the Ultrasonic Shot Peening Process_材料科学_工程科技_专业资料...RESULTS To verify the simulation model, certain velocity distributions from ...澄丁(上海)贸易有限公司
与TTOMA韩国休闲领导品牌之一，是休闲精品。它独特的款式设计与生活品位使得该品牌在庞大的生活潮流市场中，鹤立于顶尖之位。年轻、性感与真实；是现代年轻人的追求，凸显个性、讲求自由是当代人的风格；而这些有许多也正是美国服饰风格的精髓所在。于是 TOMM这样一个极具代表性、以设计掌舵人的名字为名的经典美国服饰品牌。 PEENCOCO与 TOMM品牌崇尚自然、简洁的风尚，同时设计理念中无不渗透出青春的动感活力，与美国本土的风格特点十分和谐，受到年轻一代美国人的热爱。直线上...
主要经营产品：韩国品牌女装
经营模式：商业服务
成立时间：2014
职员人数：101 - 200人
注册资本：10万元
注册地址:中国
官方网站：
诚信值：39
最新公司推荐
title="北京马甸回收纸币有限公司北京马甸回收纸币有限公司
相关信息推荐
周边城市企业名录推荐
热门城市企业名录推荐
尊敬的用户，如果您发现当前展厅有如下违法信息，请根据以下分类进行举报，感谢您对本站的支持。
温馨提示：商务联盟利用大数据技术，提供免费的搜索、查询、推广服务的电子商务平台，如您发现内容不正确或有侵权行为，请您或，若该展厅属于贵公司，则请您取回网站管理权并修正里面的内容，以便您保护好您的合法权益，马上。
商务联盟网所有服务均免费，信息均来自网络或用户发布，本站所刊载的各类形式(包括但不仅限于文字、图片、图表)的信息内容仅代表原出处或用户的观点，不代表本站的观点和看法，与本站立场无关，相关全部法律责任由原出处或用户承担，本站不对其准确性、真实性、完整性和合法性作任何直接、间接、法定、约定的保证。